路由器配置(新手上路,比较全面,强烈推荐)第一章 路由器配置基础 一、基本设置方式 二、命令状态 三、设置对话过程 四、常用命令 五、配置IP寻址 六、配置静态路由 第二章 广域网协议设置 一、HDLC 二、PPP 三、X.25 四、Frame Relay 五、ISDN 六、PSTN 第三章 路由协议设置 一、RIP协议 二、IGRP协议 三、OSPF协议 四、重新分配路由 五、IPX协议设置 第四章 服务质量及访问控制 一、协议优先级设置 二、队列定制 三、访问控制 第五章 虚拟局域网(VLAN)路由 一、虚拟局域网(VLAN) 二、交换机间链路(ISL)协议 三、虚拟局域网(VLAN)路由实例 参考第一章:路由器配置基础 一、基本设置方式 一般来说,可以用5种方式来设置路由器: 1.Console口接终端或运行终端仿真软件的微机; 2.AUX口接MODEM,通过电话线与远方的终端或运行终端仿真软件的微机相连; 3.通过Ethernet上的TFTP服务器; 4.通过Ethernet上的TELNET程序; 5.通过Ethernet上的SNMP网管工作站。 但路由器的第一次设置必须通过第一种方式进行,此时终端的硬件设置如下: 波特率 :9600 数据位 :8 停止位 :1 奇偶校验: 无 二、命令状态 1. router> 路由器处于用户命令状态,这时用户可以看路由器的连接状态,访问其它网络和主机,但不能看到和更改路由器的设置内容。 2. router# 在router>提示符下键入enable,路由器进入特权命令状态router#,这时不但可以执行所有的用户命令,还可以看到和更改路由器的设置内容。 3. router(config)# 在router#提示符下键入configure terminal,出现提示符router(config)#,此时路由器处于全局设置状态,这时可以设置路由器的全局参数。 4. router(config-if)#; router(config-line)#; router(config-router)#;… 路由器处于局部设置状态,这时可以设置路由器某个局部的参数。 5. > 路由器处于RXBOOT状态,在开机后60秒内按ctrl-break可进入此状态,这时路由器不能完成正常的功能,只能进行软件升级和手工引导。 设置对话状态 这是一台新路由器开机时自动进入的状态,在特权命令状态使用SETUP命令也可进入此状态,这时可通过对话方式对路由器进行设置。 三、设置对话过程 显示提示信息 全局参数的设置 接口参数的设置 显示结果 利用设置对话过程可以避免手工输入命令的烦琐,但它还不能完全代替手工设置,一些特殊的设置还必须通过手工输入的方式完成。 进入设置对话过程后,路由器首先会显示一些提示信息: --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. 这是告诉你在设置对话过程中的任何地方都可以键入“?”得到系统的帮助,按ctrl-c可以退出设置过程,缺省设置将显示在‘[]’中。然后路由器会问是否进入设置对话: Would you like to enter the initial configuration dialog? [yes]: 如果按y或回车,路由器就会进入设置对话过程。首先你可以看到各端口当前的状况: First, would you like to see the current interface summary? [yes]: Any interface listed with OK? value "NO" does not have a valid configuration Interface IP-Address OK? Method Status Protocol Ethernet0 unassigned NO unset up up Serial0 unassigned NO unset up up ……… ……… … …… … … 然后,路由器就开始全局参数的设置: Configuring global parameters: 1.设置路由器名: Enter host name [Router]: 2.设置进入特权状态的密文(secret),此密文在设置以后不会以明文方式显示: The enable secret is a one-way cryptographic secret used instead of the enable password when it exists. Enter enable secret: cisco 3.设置进入特权状态的密码(password),此密码只在没有密文时起作用,并且在设置以后会以明文方式显示: The enable password is used when there is no enable secret and when using older software and some boot images. Enter enable password: pass 4.设置虚拟终端访问时的密码: Enter virtual terminal password: cisco 5.询问是否要设置路由器支持的各种网络协议: Configure SNMP Network Management? [yes]: Configure DECnet? [no]: Configure AppleTalk? [no]: Configure IPX? [no]: Configure IP? [yes]: Configure IGRP routing? [yes]: Configure RIP routing? [no]: ……… 6.如果配置的是拨号访问服务器,系统还会设置异步口的参数: Configure Async lines? [yes]: 1) 设置线路的最高速度: Async line speed [9600]: 2) 是否使用硬件流控: Configure for HW flow control? [yes]: 3) 是否设置modem: Configure for modems? [yes/no]: yes 4) 是否使用默认的modem命令: Configure for default chat s cript? [yes]: 5) 是2004-1-10 21:15 aqbhc 六、配置静态路由 通过配置静态路由,用户可以人为地指定对某一网络访问时所要经过的路径,在网络结构比较简单,且一般到达某一网络所经过的路径唯一的情况下采用静态路由。 任务 命令 建立静态路由 ip route prefix mask {address | interface} [distance] [tag tag] [permanent] Prefix :所要到达的目的网络 mask :子网掩码 address :下一个跳的IP地址,即相邻路由器的端口地址。 interface :本地网络接口 distance :管理距离(可选) tag tag :tag值(可选) permanent :指定此路由即使该端口关掉也不被移掉。以下在Router1上设置了访问192.1.0.64/26这个网下一跳地址为192.200.10.6,即当有目的地址属于 192.1.0.64/26的网络范围的数据报,应将其路由到地址为192.200.10.6的相邻路由器。在Router3上设置了访问 192.1.0.128/26及192.200.10.4/30这二个网下一跳地址为192.1.0.65。由于在Router1上端口Serial 0地址为192.200.10.5,192.200.10.4/30这个网属于直连的网,已经存在访问192.200.10.4/30的路径,所以不需要 在Router1上添加静态路由。 Router1: ip route 192.1.0.64 255.255.255.192 192.200.10.6 Router3: ip route 192.1.0.128 255.255.255.192 192.1.0.65 ip route 192.200.10.4 255.255.255.252 192.1.0.65 同时由于路由器Router3除了与路由器Router2相连外,不再与其他路由器相连,所以也可以为它赋予一条默认路由以代替以上的二条静态路由, ip route 0.0.0.0 0.0.0.0 192.1.0.65 即只要没有在路由表里找到去特定目的地址的路径,则数据均被路由到地址为192.1.0.65的相邻路由器。 第二章:广域网协议设置 一、HDLC HDLC是CISCO路由器使用的缺省协议,一台新路由器在未指定封装协议时默认使用HDLC封装。 1. 有关命令 端口设置 任务 命令 设置HDLC封装 encapsulation hdlc 设置DCE端线路速度 clockrate speed 复位一个硬件接口 clear interface serial unit 显示接口状态 show interfaces serial [unit] 1 注:1.以下给出一个显示Cisco同步串口状态的例子. Router#show interface serial 0 Serial 0 is up, line protocol is up Hardware is MCI Serial Internet address is 150.136.190.203, subnet mask is 255.255.255.0 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) Last input 0:00:07, output 0:00:00, output hang never Output queue 0/40, 0 drops; input queue 0/75, 0 drops Five minute input rate 0 bits/sec, 0 packets/sec Five minute output rate 0 bits/sec, 0 packets/sec 16263 packets input, 1347238 bytes, 0 no buffer Received 13983 broadcasts, 0 runts, 0 giants 2 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 2 abort 22146 packets output, 2383680 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets, 0 restarts 1 carrier transitions 2. 举例
设置如下: Router1: interface Serial0 ip address 192.200.10.1 255.255.255.0 clockrate 1000000 Router2: interface Serial0 ip address 192.200.10.2 255.255.255.0 ! 3. 举例使用E1线路实现多个64K专线连接. 相关命令: 任务 命令 进入controller配置模式 controller {t1 | e1} number 选择帧类型 framing {crc4 | no-crc4} 选择line-code类型 linecode {ami | b8zs | hdb3} 建立逻辑通道组与时隙的映射 channel-group number timeslots range1 显示controllers接口状态 show controllers e1 [slot/port]2注: 1. 当链路为T1时,channel-group编号为0-23, Timeslot范围1-24; 当链路为E1时, channel-group编号为0-30, Timeslot范围1-31. 2.使用show controllers e1观察controller状态,以下为帧类型为crc4时controllers正常的状态. Router# show controllers e1 e1 0/0 is up. Applique type is Channelized E1 - unbalanced Framing is CRC4, Line Code is HDB3 No alarms detected. Data in current interval (725 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 24 hours) 0 Line Code Violations, 0 Path Code Violations, 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs 以下例子为E1连接3条64K专线, 帧类型为NO-CRC4,非平衡链路,路由器具体设置如下: shanxi#wri t Building configuration... Current configuration: ! version 11.2 no service udp-small-servers no service tcp-small-se2004-1-10 21:16 aqbhc 三、x.25 1. X25技术 X.25规范对应OSI三层,X.25的第 三层描述了分组的格式及分组交换的过程。X.25的第二层由LAPB(Link Access Procedure, Balanced)实现,它定义了用于DTE/DCE连接的帧格式。X.25的第一层定义了电气和物理端口特性。 X.25网络设备分为数据终端设 备(DTE)、数据电路终端设备(DCE)及分组交换设备(PSE)。DTE是X.25的末端系统,如终端、计算机或网络主机,一般位于用户端, Cisco路由器就是DTE设备。DCE设备是专用通信设备,如调制解调器和分组交换机。PSE是公共网络的主干交换机。 X.25定义了数据通讯 的电话网络,每个分配给用户的x.25 端口都具有一个x.121地址,当用户申请到的是SVC(交换虚电路)时,x.25一端的用户在访问另一端的用户时,首先将呼叫对方x.121地址,然后 接收到呼叫的一端可以接受或拒绝,如果接受请求,于是连接建立实现数据传输,当没有数据传输时挂断连接,整个呼叫过程就类似我们拨打普通电话一样,其不同 的是x.25可以实现一点对多点的连接。其中x.121地址、htc均必须与x.25服务提供商分配的参数相同。X.25 PVC(永久虚电路),没有呼叫的过程,类似DDN专线。 2. 有关命令: 任务 命令 设置X.25封装 encapsulation x25 [dce] 设置X.121地址 x25 address x.121-address 设置远方站点的地址映射 x25 map protocol address [protocol2 address2[...[protocol9 address9]]] x121-address [option] 设置最大的双向虚电路数 x25 htc citcuit-number1 设置一次连接可同时建立的虚电路数 x25 nvc count2 设置x25在清除空闲虚电路前的等待周期 x25 idle minutes 重新启动x25,或清一个svc,启动一个pvc相关参数 clear x25 {serial number | cmns-interface mac-address} [vc-number] 3 清x25虚电路 clear x25-vc 显示接口及x25相关信息 show interfaces serial show x25 interface show x25 map show x25 vc 注:1、虚电路号从1到4095,Cisco路由器默认为1024,国内一般分配为16。 2、虚电路计数从1到8,缺省为1。 3、 在改变了x.25各层的相关参数后,应重新启动x25(使用clear x25 {serial number | cmns-interface mac-address} [vc-number]或clear x25-vc命令),否则新设置的参数可能不能生效。同时应对照服务提供商对于x.25交换机端口的设置来配置路由器的相关参数,若出现参数不匹配则可能 会导致连接失败或其它意外情况。 3. 实例: 3.1. 在以下实例中每二个路由器间均通过svc实现连接。 路由器设置如下: Router1: interface Serial0 encapsulation x25 ip address 192.200.10.1 255.255.255.0 x25 address 110101 x25 htc 16 x25 nvc 2 x25 map ip 192.200.10.2 110102 broadcast x25 map ip 192.200.10.3 110103 broadcast !Router2: interface Serial0 encapsulation x25 ip address 192.200.10.2 255.255.255.0 x25 address 110102 x25 htc 16 x25 nvc 2 x25 map ip 192.200.10.1 110101 broadcast x25 map ip 192.200.10.3 110103 broadcast !Router: interface Serial0 encapsulation x25 ip address 192.200.10.3 255.255.255.0 x25 address 110103 x25 htc 16 x25 nvc 2 x25 map ip 192.200.10.1 110101 broadcast x25 map ip 192.200.10.2 110102 broadcast !相关调试命令: clear x25-vc show interfaces serial show x25 map show x25 route show x25 vc 3.2. 在以下实例中路由器router1和router2均通过svc与router连接,但router1和router2不通过svc直接连接,此三个路由 器的串口运行RIP路由协议,使用了子接口的概念。由于使用子接口,router1和router2均学习到了访问对方局域网的路径,若不使用子接口, router1和router2将学不到到对方局域网的路由。子接口(Subinterface)是一个物理接口上的多个虚接口,可以用于在同一个物理接口上连接多个网。我们知道为了避免路由循环,路由器支持split horizon法则,它只允许路由更新被分配到路由器的其它接口,而不会再分配路由更新回到此路由被接收的接口。 无 论如何,在广域网环境使用基于连接的接口(象 X.25和Frame Relay),同一接口通过虚电路(vc)连接多台远端路由器时,从同一接口来的路由更新信息不可以再被发回到相同的接口,除非强制使用分开的物理接口连 接不同的路由器。Cisco提供子接口(subinterface)作为分开的接口对待。你可以将路由器逻辑地连接到相同物理接口的不同子接口, 这样来自不同子接口的路由更新就可以被分配到其他子接口,同时又满足split horizon法则。Router1: interface Serial0 encapsulation x25 ip address 192.200.10.1 255.255.255.0 x25 address 110101 x25 htc 16 x25 nvc 2 x25 map ip 192.200.10.3 110103 broadcast ! router rip network 192.200.10.0 !Router2: interface Serial0 encapsulation x25 ip address 192.200.11.2 255.255.255.0 x25 address 110102 x25 htc 16 x252004-1-10 21:16 aqbhc 四、Frame Relay 1. 帧中继技术 帧中继是一种高性能的WAN 协议,它运行在OSI参考模型的物理层和数据链路层。它是一种数据包交换技术,是X.25的简化版本。它省略了X.25的一些强健功能,如提供窗口技术和 数据重发技术,而是依靠高层协议提供纠错功能,这是因为帧中继工作在更好的WAN设备上,这些设备较之X.25的WAN设备具有更可靠的连接服务和更高的 可靠性,它严格地对应于OSI参考模型的最低二层,而X.25还提供第三层的服务,所以,帧中继比X.25具有更高的性能和更有效的传输效率。 帧中继广域网的设备分为数据终端设备(DTE)和数据电路终端设备(DCE),Cisco路由器作为 DTE设备。 帧 中继技术提供面向连接的数据链路层的通信,在每对设备之间都存在一条定义好的通信链路,且该链路有一个链路识别码。这种服务通过帧中继虚电路实现,每个帧 中继虚电路都以数据链路识别码(DLCI)标识自己。DLCI的值一般由帧中继服务提供商指定。帧中继即支持PVC也支持SVC。 帧中继本地管理接口(LMI)是对基本的帧中继标准的扩展。它是路由器和帧中继交换机之间信令标准,提供帧中继管理机制。它提供了许多管理复杂互联网络的特性,其中包括全局寻址、虚电路状态消息和多目发送等功能。 2. 有关命令: 端口设置 任务 命令 设置Frame Relay封装 encapsulation frame-relay[ietf] 1 设置Frame Relay LMI类型 frame-relay lmi-type {ansi | cisco | q933a}2 设置子接口 interface interface-type interface-number.subinterface-number [multipoint|point-to-point] 映射协议地址与DLCI frame-relay map protocol protocol-address dlci [broadcast]3 设置FR DLCI编号 frame-relay interface-dlci dlci [broadcast] 注:1.若使Cisco路由器与其它厂家路由设备相连,则使用Internet工程任务组(IETF)规定的帧中继封装格式。 2.从Cisco IOS版本11.2开始,软件支持本地管理接口(LMI)“自动感觉”, “自动感觉”使接口能确定交换机支持的LMI类型,用户可以不明确配置LMI接口类型。 3.broadcast选项允许在帧中继网络上传输路由广播信息。 4. ISDN访问首都在线263网实例: 本地局部网地址为10.0.0.0/24,属于保留地址,通过NAT地址翻译功能,局域网用户可以通过ISDN上263网访问Internet。263的ISDN电话号码为2633,用户为263,口令为263,所涉及的命令如下表: 任务 命令 指定接口通过PPP/IPCP地址协商获得IP地址 ip address negotiated 指定内部和外部端口 ip nat {inside | outside} 使用ppp/pap作认证 ppp authentication pap callin 指定接口属于拨号组1 dialer-group 1 定义拨号组1允许所有IP协议 dialer-list 1 protocol ip permit 设定拨号,号码为2633 dialer string 2633 设定登录263的用户名和口令 ppp pap sent-username 263 password 263 设定默认路由 ip route 0.0.0.0 0.0.0.0 bri 0 设定符合访问列表2的所有源地址被翻译为bri 0所拥有的地址 ip nat inside source list 2 interface bri 0 overload 设定访问列表2,允许所有协议 access-list 2 permit any 具体配置如下: hostname Cisco2503 ! isdn switch-type basic-net3 ! ip subnet-zero no ip domain-lookup ip routing ! interface Ethernet 0 ip address 10.0.0.1 255.255.255.0 ip nat inside no shutdown ! interface Serial 0 shutdown no des cription no ip address ! interface Serial 1 shutdown no des cription no ip address ! interface bri 0 ip address negotiated ip nat outside encapsulation ppp ppp authentication pap callin ppp multilink dialer-group 1 dialer hold-queue 10 dialer string 2633 dialer idle-timeout 120 ppp pap sent-username 263 password 263 no cdp enable no ip split-horizon no shutdown ! ip classless ! ! Static Routes ! ip route 0.0.0.0 0.0.0.0 bri 0 ! ! Access Control List 2 ! access-list 2 permit any ! dialer-list 1 protocol ip permit ! ! Dynamic NAT ! ip nat inside source list 2 interface bri 0 overload snmp-server community public ro ! line console 0 exec-timeout 0 0 ! line vty 0 4 ! end 5. Cisco765M通过ISDN拨号上263 由于Cisco765的设置命令与我们常用的Cisco路由器的命令不同,所以以下列举了通过Cisco765上263访问Internet的具体命令行设置步骤。 >set system c765 c765> set multidestination on c765> set switch net3 c765> set ppp multilink on c765> cd lan c765:LAN> set ip routing on c765:LAN> set ip address 10.0.0.1 c765:LAN> set ip netmask 255.0.0.0 c765:LAN> set briding off c765:LAN>cd c765> set user remotenet New user remotenet being created c765:remotenet> set ip routing on c765:remotenet> set bri2004-1-10 21:16 aqbhc 1.2. Access Server通过Tacacs服务器实现安全认证: 使用一台WINDOWS NT服务器作为Tacacs服务器,地址为10.111.4.2,运行Cisco2511随机带的Easy ACS 1.0软件实现用户认证功能. 相关设置: 任务 命令 激活AAA访问控制 aaa new-model 用户登录时默认起用Tacacs+做AAA认证 aaa authentication login default tacacs+ 列表名为no_tacacs使用ENABLE口令做认证 aaa authentication login no_tacacs enable 在运行PPP的串行线上采用Tacacs+做认证 aaa authentication ppp default tacacs+ 由TACACS+服务器授权运行EXEC aaa authorization exec tacacs+ 由TACACS+服务器授权与网络相关的服务请求。 aaa authorization network tacacs+ 为EXEC会话运行记帐.进程开始和结束时发通告给TACACS+服务器。 aaa accounting exec start-stop tacacs+ 为与网络相关的服务需求运行记帐包括SLIP,PPP,PPP NCPs,ARAP等.在进程开始和结束时发通告给TACACS+服务器。 aaa accounting network start-stop tacacs+ 指定Tacacs服务器地址 tacacs-server host 10.111.4.2 在Tacacs+服务器和访问服务器设定共享的关键字,访问服务器和Tacacs+服务器使用这个关键字去加密口令和响应信息。这里使用tac作为关键字。 tacacs-server key tac 访问服务器设置如下: hostname router ! aaa new-model aaa authentication login default tacacs+ aaa authentication login no_tacacs enable aaa authentication ppp default tacacs+ aaa authorization exec tacacs+ aaa authorization network tacacs+ aaa accounting exec start-stop tacacs+ aaa accounting network start-stop tacacs+ enable secret 5 $1$kN4g$CvS4d2.rJzWntCnn/0hvE0 ! interface Ethernet0 ip address 10.111.4.20 255.255.255.0 ! interface Serial0 no ip address shutdown interface Serial1 no ip address shutdown ! interface Group-Async1 ip unnumbered Ethernet0 encapsulation ppp async mode interactive peer default ip address pool Cisco2511-Group-142 no cdp enable group-range 1 16 ! ip local pool Cisco2511-Group-142 10.111.4.21 10.111.4.36 tacacs-server host 10.111.4.2 tacacs-server key tac ! line con 0 exec-timeout 0 0 password cisco login authentication no_tacacs line 1 16 login authentication tacacs modem InOut modem autoconfigure type usr_courier autocommand ppp transport input all stopbits 1 rxspeed 115200 txspeed 115200 flowcontrol hardware line aux 0 transport input all line vty 0 4 password cisco ! end 2. DDR(dial-on-demand routing)实例 此 例通过Cisco 2500系列路由器的aux端口实现异步拨号DDR连接。Router1拨号连接到Router2。其中采用PPP/CHAP做安全认证,在 Router1中应建立一个用户,以对端路由器主机名作为用户名,即用户名应为Router2。同时在Router2中应建立一个用户,以对端路由器主机 名作为用户名,即用户名应为Router1。所建的这两用户的password必须相同。 相关命令如下: 任务 命令 设置路由器与modem的接口指令 chat-s cript s cript-name EXPECT SEND EXPECT SEND (etc.) 设置端口在挂断前的等待时间 dialer idle-timeout seconds 设 置协议地址与电话号码的映射 dialer map protocol next-hop-address [name hostname] [broadcast] [modem-s cript modem-regexp] [system-s cript system-regexp] [dial-string] 设置电话号码 dialer string dial-string 指定在特定线路下路由器默认 使用的chat-s cript s cript {dialer|reset} s cript-name Router1: hostname Router1 ! enable secret 5 $1$QKI7$wXjpFqC74vDAyKBUMallw/ ! username Router2 password cisco chat-s cript cisco-default "" "AT" TIMEOUT 30 OK "ATDT /T" TIMEOUT 30 CONNECT /c ! interface Ethernet0 ip address 10.0.0.1 255.255.255.0 ! interface Async1 ip address 192.200.10.1 255.255.255.0 encapsulation ppp async default routing async mode dedicated dialer in-band dialer idle-timeout 60 dialer map ip 192.200.10.2 name Router2 modem-s cript cisco-default 573 dialer-group 1 ppp authentication chap ! ip route 10.0.1.0 255.255.255.0 192.200.10.2 dialer-list 1 protocol ip permit ! line con 0 line aux 0 modem InOut modem autoconfigure discovery flowcontrol hardware Router2: hostname Router2 ! enable secret 5 $1$F6EV$5U8puzNt2/o9g.t56PXHo. ! username Router1 password cisco ! interface Ethernet0 ip address 10.0.1.1 255.255.255.0 ! interface Async1 ip address 192.200.10.2 255.255.255.0 encapsulation ppp async default routing asyn2004-1-10 21:17 aqbhc 五、IPX协议设置
IPX协议与IP协议是两种不同的网络层协议,它们的路由协议也不一样,IPX的路由协议不象IP的路由协议那样丰富,所以设置起来比较简单。但IPX协议在以太网上运行时必须指定封装形式。 1. 有关命令 启动IPX路由 ipx routing 设置IPX网络及以太网封装形式 ipx network network [encapsulation encapsulation-type]1 指定路由协议,默认为RIP ipx router {eigrp autonomous-system-number | nlsp [tag] | rip} 注:1.network 范围是1 到FFFFFFFD. IPX封装类型列表 接口类型 封装类型 IPX帧类型 Ethernet novell-ether (默认) arpa sap snap Ethernet_802.3 Ethernet_II Ethernet_802.2 Ethernet_Snap Token Ring sap (默认) snap Token-Ring Token-Ring_Snap FDDI snap (默认) sap novell-fddi Fddi_Snap Fddi_802.2 Fddi_Raw 举例: 在 此例中,WAN的IPX网络为3a00,Router1所连接的局域网IPX网络号为2a00,在此局域网有一台Novell服务器,IPX网络号也是 2a00, 路由器接口的IPX网络号必须与在同一网络的Novell服务器上设置的IPX网络号相同。路由器通过监听SAP来建立已知的服务及自己的网络地址表,并 每60秒发送一次自己的SAP表。 Router1: ipx routing interface ethernet 0 ipx network 2a00 encapsulation sap ! interface serial 0 ipx network 3a00 ! ipx router eigrp 10 network 3a00 network 2a00 ! Router2: ipx routing interface ethernet 0 ipx network 2b00 encapsulation sap ! interface serial 0 ipx network 3a00 ! ipx router eigrp 10 network 2b00 network 3a00 ! 相关调试命令: debug ipx packet debug ipx routing debug ipx sap debug ipx spoof debug ipx spx show ipx eigrp interfaces show ipx eigrp neighbors show ipx eigrp topology show ipx interface show ipx route show ipx servers show ipx spx-spoof 第四章 服务质量及访问控制一、协议优先级设置
1.有关命令 任务 命令 设置优先级表项目 priority-list list-number protocol protocol {high | medium | normal | low} queue-keyword keyword-value 使用指定的优先级表 priority-group list-number2.举例 Router1: priority-list 1 protocol ip high tcp telnet priority-list 1 protocol ip low tcp ftp priority-list 1 default normal interface serial 0priority-group 1 二、队列定制