作者:隆重黄_927 | 来源:互联网 | 2020-09-06 00:06
linux下安装apachephp的方法:首先下载“httpd-2.2.11”并解压安装包;然后通过“makeinstall”进行编译安装;接着下载php并进行编译安装;最后修改配置文件即可。
linux下安装apache php的方法:首先下载“httpd-2.2.11”并解压安装包 ;然后通过“make install”进行编译安装;接着下载php并进行编译安装;最后修改配置文件即可。
安装apache过程总结
安装httpd-2.2.11
下载地址:http://archive.apache.org/dist/httpd/
安装过程
[root@zhibing /]# rpm -qa |grep httpd
httpd-manual-2.0.52-32.ent
httpd-suexec-2.0.52-32.ent
system-config-httpd-1.3.1-1
httpd-2.0.52-32.ent
//查看本机是否已经安装httpd
[root@zhibing /]# rpm -e httpd --nodeps
//删除本机存在的httpd
[root@zhibing tmp]# tar zxvf httpd-2.2.11.tar.gz
//解压安装包
[root@zhibing tmp]# cd httpd-2.2.11
//进入httpd-2.2.11
[root@zhibing httpd-2.2.11]# ./configure --prefix=/usr/local/apache --enable-s0
//检测程序, --prefix 软件要安装的路径–enable-so表示让apache核心装载DSO,但是不实际编译任何动态模块
[root@zhibing httpd-2.2.11]# make
//编译
[root@zhibing httpd-2.2.11]# make install
//编译后安装
安装 php-5.2.9
下载地址:http://cn.php.net/downloads.php
注意:安装php-5.2.9之前,png,gd,freetype,zlib,mysql,openssl都存在,若不存在,手动安装一下
安装过程
[root@zhibing tmp]# tar zxvf php-5.2.9.tar.gz
[root@zhibing tmp]#cd php-5.2.9.tar.gz
[root@zhibing php-5.2.9]#./configure --prefix=/usr/local/php --with-apxs2=/usr/local/apache/bin/apxs --with-png-dir --with-gd --with-freetype-dir --with-zlib --with-mysql=/usr/local/mysql --with-openssl --with-gettext -enable-sockets
//检测程序,并同时加载相关参数
[root@zhibing php-5.2.9]#make && make install
//编译安装
[root@zhibing php-5.2.9]#cp php.ini-recommended /usr/local/php/lib/php.ini
//拷贝php.ini文件启动时会读取到的配置文件
[root@zhibing php-5.2.9]#ln -s /usr/local/php/bin/* /usr/local/bin/
//连接
ot@zhibing php-5.2.9]#lvi /usr/local/apache/conf/httpd.conf
//修改配置文件
添加
AddType application/x-gzip .gz .tgz
AddType application/x-httpd-php .php
AddType p_w_picpath/x-icon .ico
添加
index.php index.html index.html.var
DirectoryIndex index.html index.php index.html index.html.var
测试:
[root@zhibing ]#vi /usr/local/apache/htdocs/test.php
//新建test.php
在新文件中添加
wq保存退出
Phpinfo是特殊的php函数,可以显示目前服务器内php模块的相关核心数据
[root@zhibing ]## /usr/local/apache/bin/apachectl –k stop
[root@zhibing ]##/usr/local/apache/bin/apachectl –k start
//重新启动apache
在浏览器中输入主机地址例如http://主机IP/test.php如有出现下面图片就说明apace安装成功
以上就是linux下如何安装apache php的详细内容,更多请关注 第一PHP社区 其它相关文章!